Richmond water heater manual

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Sustainability Partners Contact. Where to buy. Home Residential. Gas Water Heaters. Electric Water Heaters. Another possible reason is the blower is unplugged. Check to make sure it is plugged in. Verify power supply VAC. If that is not the issue, the combustion shutoff device could have tripped and you may need to contact a qualified service technician. Lastly, check the valve error codes. If there are error codes, troubleshoot to clear the error and fix the issue.

If the status light is not blinking blue, relight the pilot. If the status light blinks red more than one flash every three seconds, here is what the error code and means and what to do to clear the error:. Gas valve LEDs will light separately or together to indicate the status or an error. This indicates that the pressure switch remained closed longer than 5 seconds after the call for heat began. The LED status indicates the pressure switch remained opened longer than 5 seconds after the combustion blower was energized.

The water heater and its gas connections must be leak tested at normal operating pressures before placing it in operation.

To do so, follow the steps below:. You should also leak test the factory connections to the Combination Gas Control Thermostat after the water heater is placed in operation. To clean the burner, remove the burner from the water heater.

You can use a vacuum cleaner on the burner and floor shield inside the water heater. You can also clean the burner by scrubbing with mild detergent. The burner chamber is a sealed area and it is recommended that cleaning of the burner is done by a qualified service personnel.

If the burner access door is removed, the burner access door gasket must be replaced. Hard water deposits can therefore accumulate in the bottom of the tank. If your attempts to light the pilot burner have been unsuccessful, there could be air in the gas line. To fix this problem, you first need to purge the air from the gas line and then try again to see it will light. Another thing that can cause this problem is when the pilot burner orifice is clogged. The pilot burner should be cleaned or replaced in this case.

The pilot burner tube might be pinched or clogged, thus preventing the pilot burner from lighting. If so, you may need to clean, repair or replace the pilot burner to fix the problem. The knob needs to be depressed to light the water heater. If you are unable to light the main burner to your Richmond power vent water heater, it may be due to the following issues:. Check this too: Kinetico Water Filter Troubleshooting.

Keeping your water heater properly maintained helps ensure it operates smoothly and efficiently, it is free of problems, and serves you for many years. Below are some maintenance tips to consider:. In his spare time, Oscar loves tinkering with electronics. When he is not busy trying not to electrocute himself, you can find him in the garden tending to his vegetables and chickens. House generators are quite expensive. Therefore most homeowners try to cut down costs wherever possible, bypassing the recommended installation procedure.

Ideally, connecting a generator to any With Georgia’s plans to promote affordable and inclusive housing, the state government is slowly welcoming the tiny house community.

However, due to strict and confusing zoning codes, many tiny house Turn off all electrical power to the appliance. The water heater is equipped with a Hot Surface Ignition System which automatically lights the burner. Do not open the inner door of the appliance and try to light the burner by hand. Wait 5 minutes to clear out any gas.

If you do not smell gas, proceed to turn on all electrical power to the appliance. Set the thermostat to the desired temperature. If the appliance will not operate, turn off gas to the appliance and call your service technician or gas supplier.

Richmond direct vent water heater Follow the instructions below to light your direct vent water heater: Set the thermostat dial to the lowest setting by turning the thermostat dial clockwise until it stops. Do not force it. Slightly depress the gas control knob and turn clockwise to OFF position. Stop and follow the safety precautions as above if you smell any gas.

Go to the next step if you do not smell gas. Remove the outer door from the water heater. Do not attempt to remove the inner door. Locate the piezo-electric spark generator which is located on top of the combination gas control.

Depress and hold the gas control knob all the way down. Immediately depress the piezo-electric spark generator button several times until the pilot is lit. You can only see the flame through the sight glass window located on the inner door. Continue holding down the gas control knob for about 1 minute after the pilot is lit.

If it goes out, repeat steps 3 to 9. Once the pilot flame is established, replace the outer door. Turn the gas control knob counter-clockwise to the ON position. Tankless Electric. Speciality Water Heaters Marathon. Lightweight plastic tank will not rust; ideal in hard water applications.

Atmospheric for Manufactured Housing. Non-Condensing Tankless Gas. Space saving design with intelligent electronic controls and an all-copper heater exchanger View Product. Gas Electric Tankless Speciality.

 
https://abrendsoft.website/images/news.gif
https://brekisoofg.site/
https://klodossoft.online/index.php
https://akkpallsoft.fun/
https://klodossoft.online/index.php
https://brekisoofg.site/
https://klodossoft.pw/article
https://klodossoft.pw/
https://abrendsoft.website/images/news.png
https://abrendsoft.website/images/news.gif
https://brekisoofg.site/article
https://klodossoft.online/views/
https://klodossoft.online/views/article.php
https://abrendsoft.website/images/news.gif
 

 

Richmond water heater manual. User Manual Richmond 6G40-36F3 Water Heater

 

It features a low emission burner design, maintenance free protection, no filters to clean and standard replacement parts. Available on 9-year and year models. Rigid Foam Insulation fights stand-by heat loss. Heat Traps prevent convective heat loss, so the water heater costs less to operate.

Available on year models. For cleaning, remove the burner from the water heater. A vacuum cleaner can be used on the burner and floor shield inside the water heater. The burner can also be cleaned by scrubbing with mild detergent. If the water heater is to remain idle for an extended period of time, the power and water to the appliance should be turned off to conserve energy and prevent a build-up of dangerous hydrogen gas.

The water heater and piping should be drained if they might be subjected to freezing temperatures. Make certain the water heater is completely filled again before placing it in operation. This water heater is equipped with an anode rod designed to prolong the life of the glass lined tank. The anode rod is slowly consumed, thereby eliminating or minimizing corrosion of the glass lined tank.

Chlorination of the water supply should minimize the problem. Wiring errors can cause improper and dangerous operation. Refer repairs to qualified service personnel. Use manuals file type: PDF. Richmond – Water Heaters. Home Bookmarks Brands Reviews About us. Documents : Go to donwload! User Manual User Manual – English Specification Technical Specifications – English Other Documents Use And Care Manual – English Table of contents Installing the water heater Operating the water heater Care and cleaning of the water heater Troubleshooting Tips User Guide Water Heater Installing the water heater Location The water heater should not be located in an area where leakage from the tank or connections will result in damage to the area adjacent to the heater or to lower floors of the structure.

The water heater must be centered in the drain pan. Hot water lines should be insulated to conserve water and energy. The water heater and water lines should be protected from exposure to freezing temperatures. DO NOT install the water heater in bathrooms, bedrooms, any occupied rooms normally kept closed, or in unprotected outdoor areas.

If the water heater is installed in an alcove or closet, the entire floor must be covered by a wood or metal panel. A minimum of 24 in. The water heater may be installed on combustible floors, but not directly on carpeting. If the water heater must be installed on carpeting, place a metal or wood panel beneath the water heater, extending beyond its full width and depth at least 3 in.

Inspect Shipment Inspect the water heater for possible damage. Check the markings on the rating plate of the water heater to be certain the type of gas supplied corresponds to the water heater requirements Combustion and Ventilation Air Proper operation of the water heater requires air for combustion and ventilation.

Provisions for combustion and ventilation air must comply with referenced codes and standards. The air must be supplied through two permanent openings of equal area.

One is to be located within 12 in. Buildings of unusually tight construction shall have the combustion and ventilation air supplied from outdoors, or a freely ventilated attic or crawl space. If ducts are used, the minimum dimensions of rectangular air ducts shall not be less than 3 in NOTICE : If the duct openings which supply combustion and ventilation air are to be covered with a protective screen or grill, the net free area openings in the material of the covering material must be used in determining the size of the openings.

Corrosive Atmospheres The air in beauty shops, dry cleaning establishments, photo processing labs, and storage areas for liquid and powdered bleaches or swimming pool chemicals often contain such halogenated hydrocarbons An air supply containing halogenated hydrocarbons may be safe to breathe, but when it passes through a gas flame corrosive elements are released that will shorten the life of any gas burning appliance. The water heater warranty is voided when failure of the heater is due to operation in a corrosive atmospher Thermal Expansion Determine if a check valve exists in the inlet water line.

Water Supply Connections Refer to the illustration below for suggested typical installation. To Fill the Water Heater Make certain that the drain valve is closed, then open the shut-off valve in the cold water supply line on the water heater.

DO NOT allow the flammable vapour sensor to become submerged in water. Condensation Condensation can form on the tank when it is first filled with water. Drops of water falling on the burner can produce a sizzling or pinging soun This condition is not unusual, and will disappear after the water becomes heated.

Leak Testing The water heater and its gas connections must be leak tested at normal operating pressures before it is placed in operation. Turn on the manual gas shut-off valve near the water heater. Use a soapy water solution to test for leaks at all connections and fittings. Bubbles indicate a gas leak that must be corrected. Venting This water heater is a Category I -Fanassisted appliance. This water heater must be vented with either three 3 inch or four 4 inch, double wall, Type B vent connectors as shown below.

Vent connectors must be securely attached to the inducer outlet to connect the water heater to the gas vent or chimney. The vent connectors must be the same size diameter as the inducer outlet or larger, never smaller. For proper venting in certain installations a larger vent connector size may be needed.

Multi-story and common venting is permitted. Vent joints must be securely fastened by sheet metal screws or other approved method. Wiring If local codes permit, the water heater may be connected to electric service with the power cord provided DO NOT use an extension cord. The maximum current draw is approximately 5. Refer to the figures below for water heater internal wiring. Hot and Cold Pipe Insulation Installation For increased energy efficiency, some water heaters have been supplied with two 24 in.

Please install the insulation, according to the illustrations above, that best meets your requirements. During Installation of this water heater DO DO check inlet gas pressure with main burner ON to ensure that it is within the range specified on the rating plate. DO maintain proper clearances to combustibles as specified on the rating plate. DO contact a qualified service technician if the main burner will not stay lit.

The burner chamber is designed to be sealed utilizing a gasket and tamper resistant screws. This should only be done by a qualified service technician.

No valve of any type should be installed between the relief valve and the tank. Local codes shall govern the installation of relief valves. Non-metallic piping, dielectric unions, flexible connectors etc. Insulation Blankets! Insulation blankets, available to the general public, for external use on electric water heaters are not necessary. The purpose of an insulation blanket is to reduce the standby heat loss encountered with storage tank heaters.

Installing the water heater Relief Valve Insulation Installation! Installation Checklist A. Operating the water heater CAUTION: Hydrogen gas can be produced in a hot water system served by this water heater that has not been used for a long period of time generally two weeks or more.

To dissipate such gas and to reduce risk of injury, it is recommended that the hot water faucet be opened for several minutes at the kitchen sink before using any electrical appliance connected to the hot water system.

The lower the temperature setting, the greater the savings in energy and operating costs. This mode will reduce the water temperature to save energy during times when hot water is not needed. See below for further options. Care and cleaning of the water heater. Our watt heating elements provide more hot water on year water heaters.

Available on 9-year and year models. Rigid Foam Insulation fights stand-by heat loss. Heat Traps prevent convective heat loss, so the water heater costs less to operate.

 
https://klodossoft.pw/views/article.php
https://akkpallsoft.website/article
https://akkpallsof21.online/views/index.php
https://brekisoofg.site/views/index.php
https://brekisoofg.site/views/
https://abrendsoft.website/index.php
https://abrendsoft.website/views/
https://brekisoofg.site/sitemap.xml

https://klodossoft.pw/views/article.php
https://abrendsoft.website/images/news.gif
https://abrendsoft.website/images/news.gif
https://klodossoft.online/sitemap.xml
https://klodossoft.online/index.php
 

Richmond water heater manual

 
https://akkpallsof21.online/views/article.php
https://abrendsoft.website/views/article.php
https://brekisoofg.site/
https://abrendsoft.website/images/news.png
https://abrendsoft.website/index.php
https://brekisoofg.site/views/index.php
https://klodossoft.online/views/article.php
https://abrendsoft.website/images/news.gif
https://klodossoft.pw/sitemap.xml
https://akkpallsoft.fun/views/index.php
https://klodossoft.online/
https://akkpallsof21.online/views/article.php
https://akkpallsoft.website/views/index.php
https://akkpallsoft.website/index.php
 
All Richmond water heaters come with detailed installation instructions. Some stores also offer professional installation services. PDF User Manual for Richmond Water Heaters Use Manual. Pdf user manuals. Richmond 6V40FT3 Essential® 40 Gallon 6-Year 34, BTU Mobile Home Natural.